富美家室内门安装维护攻略

Installation and Maintenance Guide for Fumijia Indoor Doors

一、安装篇：科学施工确保十年品质

1、 Installation article: Scientific construction ensures ten-year quality

1. 安装前的核心准备

1. Core preparation before installation

环境检测：使用温湿度计（如得力 8809）检测安装环境，要求湿度≤75%、温度 15-25℃。若湿度超标，需提前 3 天开启除湿机（推荐格力 DH20EH）。

Environmental detection: Use a temperature and humidity meter (such as Deli 8809) to detect the installation environment, requiring humidity ≤ 75% and temperature 15-25 ℃. If the humidity exceeds the standard, the dehumidifier (recommended Gree DH20EH) should be turned on 3 days in advance.

材料验收：

Material acceptance:

门扇对角线误差≤1.5mm（用 5m 卷尺测量）

Diagonal error of door leaf ≤ 1.5mm (measured with a 5m tape measure)

表面平整度：2m 靠尺检测误差≤0.5mm

Surface flatness: 2m ruler detection error ≤ 0.5mm

封边完整性：热弯封边门圆弧处需无缝隙，铝封边门氧化层无破损

Edge integrity: There should be no gaps at the arc of the hot bending edge sealing door, and the oxide layer of the aluminum edge sealing door should not be damaged

2. 门套安装的关键工艺

2. Key processes for installing door frames

膨胀螺栓固定：采用 M6×60mm 不锈钢膨胀螺栓，间距≤500mm，门框垂直度误差≤2mm（用激光水平仪校准）。

Expansion bolt fixation: M6 × 60mm stainless steel expansion bolts are used with a spacing of ≤ 500mm, and the verticality error of the door frame is ≤ 2mm (calibrated with a laser level).

发泡胶填充：聚氨酯发泡胶（如东洋胶业）填充厚度 15-20mm，固化后切除多余部分，避免挤压门扇。

Foam filling: Polyurethane foam (such as Toyo Rubber) is filled with a thickness of 15-20mm, and excess parts are cut off after curing to avoid squeezing the door leaf.

密封条安装：三元乙丙胶条（硬度 50 Shore A）需预留 3-5mm 伸缩量，用 3M 双面胶固定，避免出现漏光缝隙。

Sealing strip installation: EPDM rubber strip (hardness 50 Shore A) needs to reserve 3-5mm expansion and contraction, and be fixed with 3M double-sided tape to avoid light leakage gaps.

3. 门扇安装的技术要点

3. Technical points for door leaf installation

合页开槽：使用 3mm 木工凿精准开槽，深度与合页厚度一致（推荐史丹利 55-020）。

Joint slotting: Use a 3mm woodworking chisel to accurately slot, with a depth consistent with the thickness of the joint (recommended Stanley 55-020).

门缝控制：

Door gap control:

上缝 2-3mm，侧缝 2-2.5mm，下缝 6-8mm（用塞尺测量）

Upper seam 2-3mm, side seam 2-2.5mm, lower seam 6-8mm (measured with a feeler gauge)

热弯封边门需预留 0.5mm 热胀冷缩间隙

The hot bending edge sealing door needs to reserve a 0.5mm gap for thermal expansion and contraction

五金件安装：

Hardware installation:

锁体开孔：专用 35mm 开孔器（如博世 PBM 35）

Lock body opening: specialized 35mm hole opener (such as Bosch PBM 35)

地吸安装：吸力≥50N，距门扇底部 150mm

Ground suction installation: suction force ≥ 50N, 150mm from the bottom of the door leaf

4. 特殊结构处理

4. Special structural treatment

热弯封边门：封边温度 180-220℃，压力 8-12MPa，切割后需用同色 ABS 封边条二次封边。

Hot bending edge sealing door: The sealing temperature is 180-220 ℃, and the pressure is 8-12MPa. After cutting, ABS edge sealing strips of the same color are required for secondary sealing.

铝封边门：环氧树脂胶（如 3M DP460）粘合，固化时间≥24 小时，安装时覆盖 3M 保护膜防划伤。

Aluminum sealed edge door: bonded with epoxy resin adhesive (such as 3M DP460), curing time ≥ 24 hours, covered with 3M protective film to prevent scratches during installation.

二、维护篇：全周期保养方案

2、 Maintenance section: Full cycle maintenance plan

1. 日常清洁规范

1. Daily cleaning standards

表面护理：

Surface care:

污渍处理：中性清洁剂（pH 值 7-8）+ 超细纤维布（如 3M 思高）

Stain treatment: Neutral cleaner (pH 7-8)+ultra-fine fiber cloth (such as 3M Sigao)

划痕修复：轻微划痕用牙膏研磨，深度划痕用同色修补膏（如富美家原厂修补套装）

Scratch repair: For minor scratches, grind them with toothpaste, and for deep scratches, use the same color repair paste (such as the original Fumeijia repair kit)

五金件保养：

Hardware maintenance:

合页、锁舌：每月滴加锂基润滑脂（如克鲁勃 GEM4）

Folds and tongue locks: Add lithium based grease (such as Krupp GEM4) every month

拉手：定期检查螺丝扭矩（2-3N?m）

Handle: Regularly check the screw torque (2-3N? M)

2. 周期性维护计划

2. Periodic maintenance plan

年度保养：

Annual maintenance:

更换密封条（建议使用富美家原厂配件）

Replace the sealing strip (it is recommended to use original accessories from Fumijia)

检查门扇底部防尘条，磨损超 2mm 需更换

Check the dust strip at the bottom of the door leaf. If it is worn beyond 2mm, it needs to be replaced

防火性能检测：

Fire performance testing:

每 2 年委托第三方检测耐火时间（A 级≥1.5 小时）

Entrust a third-party to test the fire resistance time every 2 years (Grade A ≥ 1.5 hours)

避免粘贴易燃装饰物

Avoid pasting flammable decorations

3. 特殊场景应对

3. Response to special scenarios

高湿度环境：

High humidity environment:

卫生间门：每月用除湿机控制湿度≤60%，底部加装防潮铝型材

Toilet door: Use a dehumidifier to control humidity ≤ 60% every month, and install moisture-proof aluminum profiles at the bottom

厨房门：使用不锈钢清洁剂（pH4-6）去除油渍

Kitchen door: Use stainless steel cleaner (pH 4-6) to remove oil stains

医疗场所：

Medical facilities:

每周用含银离子清洁剂（浓度 0.01-0.05%）擦拭，维持抗菌率≥99%

Wipe with silver ion cleaner (concentration 0.01-0.05%) every week to maintain an antibacterial rate of ≥ 99%

每季度紫外线消毒 30 分钟

UV disinfection for 30 minutes every quarter

本文由富美家室内门友情奉献.更多有关的知识请点击:http://www.fumeijia.net我们将会对您提出的疑问进行详细的解答，欢迎您登录网站留言.

This article is a friendly contribution from Fumijia Interior Door For more information, please click: http://www.fumeijia.net We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message