现在家庭装修，不少人喜欢选择防火板装饰板，那么防火板装饰板施工要注意的问题有哪些，也是人们关心的重点，人们要求的防火板装饰板既美观又要实用，这些问题不断的被提出，现在，就让我们一起了解一下吧。

Now, many people like to choose fire-resistant decorative board for home decoration. What problems should be paid attention to in the construction of fire-resistant decorative board are also the key points that people care about. The fire-resistant decorative board that people require is both beautiful and practical. These problems have been constantly raised. Now, let's get to know it together.

1、找位与弹线：防火板装饰板安装前应根据设计图集要求，事先找好标高，平面位置、竖向尺寸进行弹线。核查预埋件及洞口：弹线后检查预埋件，木砖或木楔是否符合设计要求，排列间距尺寸、位置是否满足钉装龙骨的要求；量测门窗及洞口位置尺寸是否方正垂直且与设计要求是否相符。

1. Locating and snapping lines: Before the installation of fireproof board decorative plate, the elevation, plane position and vertical dimension shall be determined in advance according to the requirements of the design drawings. Check the embedded parts and holes: after snapping the line, check whether the embedded parts, wood bricks or wooden wedges meet the design requirements, and whether the arrangement spacing size and position meet the requirements for nailing keel; Measure whether the position and size of doors, windows and openings are square and vertical and conform to the design requirements.

2、铺、涂防潮层：设计有防潮要求时木护墙、木龙骨安装须找方、找直，骨架与木砖间的空隙应垫木垫，每块木砖至少用2个钉子钉牢，再装钉龙骨时应预留出板面厚度。木龙骨与墙体接触面要进行防腐处理，其余三面进行不少于三遍的防火涂料的处理。

2. Paving and painting damp proof course: when the design requires damp proof, the installation of wooden parapet wall and wooden keel must be square and straight. The gap between the skeleton and the wooden bricks should be padded with wood pads. Each wooden brick should be nailed with at least 2 nails. The thickness of the board should be reserved when the keel is installed. The contact surface between the wooden keel and the wall shall be treated with anti-corrosion, and the other three surfaces shall be treated with at least three times of fireproof coating.

3、安装面板：面板选色陪纹：面板进场使用前，按同房间、临近部位的用量进行挑选，是安装后从观感上木纹、颜色一致。裁板配制：按龙骨排尺，大于龙骨间距进行裁板，据裁后大面应净光（胶合板材严禁侧净），小面刮直。面板长向对接配制时须考虑接头位于横撑处，板背面应做卸力槽，以防板扭曲变形，一般卸力槽间距为100mm，槽宽10mm，槽深6－8mm。

3. Installation panel: color matching of panel: before the panel is put into use, it shall be selected according to the amount of the same room and adjacent parts, so that the wood grain and color are consistent from the appearance after installation. Cutting preparation: cut the board according to the keel arrangement, which is greater than the keel spacing. After cutting, the large surface should be clean (plywood should not be clean on the side), and the small surface should be straight. When preparing the longitudinal butt joint of the panel, it must be considered that the joint is located at the cross brace, and the back of the panel should be provided with a relief slot to prevent the panel from twisting and deformation. Generally, the spacing of the relief slot is 100mm, the slot width is 10mm, and the slot depth is 6-8mm.

4、面板安装：面板安装前对龙骨位置、平直度、钉设牢固情况、防潮层等构造要求进行检查，合格后进行安装；面板配好后进行试装，面板尺寸、接缝、接头处构造完全合适，木纹方向、颜色观感尚可的情况下，才能正式进行安装；

4. Panel installation: before panel installation, check the keel position, straightness, firmness of nails, moisture-proof course and other structural requirements, and install after passing the inspection; Trial assembly shall be carried out after the panel is assembled. Formal installation can only be carried out when the panel size, joint and joint structure are completely appropriate and the wood grain direction and color appearance are acceptable;

面板接头处安装时应涂胶与龙骨钉牢，钉固面板的钉子规格应适宜，钉子长度约为面板厚度的2－2．5倍，钉子间距一般为100mm，钉帽应砸扁，并用冲子将钉帽顺木纹方向冲入面板1－2mm；钉贴脸：贴脸料应进行挑选、花纹、颜色应与框料、面板近似。贴脸的规格尺寸、厚度应一致，接茬应顺平无错槎。

When installing the panel joint, it should be coated with glue and nailed firmly to the keel. The specification of the nails used to nail the panel should be appropriate. The length of the nails should be about 2-2.5 times the thickness of the panel. The spacing between nails is generally 100mm. The nail cap should be flattened and punched into the panel 1-2mm along the direction of the wood grain; Nail facing: The facing materials shall be selected, and the patterns and colors shall be similar to those of the frame materials and panels. The specification, size and thickness of the veneer shall be consistent, and the joints shall be smooth without any wrong joint.

所以这就是为什么我们说，防火板装饰板施工建议按照一定操作规范使用，只有这样，才会让问题尽量避免不出现。您对此还有什么问题，就来我们网站https://www.fumeijia.net进行了解吧！

So this is why we say that it is recommended to use the fireproof board decorative board according to certain operating specifications. Only in this way can problems be avoided as far as possible. If you have any questions about this, please come to our website https://www.fumeijia.net Get to know!