抗倍特板材作为高密度的人造板材，质地很坚硬。因此富美家抗倍特板厂家认为，使用抗倍特工作时应注意砂磨与拼接操作。

As a high density artificial board, the quality of the anti Beite board is very hard. Therefore, the manufacturer of Fumeijia MP laminate believes that sanding and splicing should be paid attention to when using MP laminate.

砂磨时，按顺序分别采用80＃、220＃和320＃砂纸对边缘进行砂磨。打磨速度以2.5米/15-20分钟为基准。打磨时，应注意不要损坏表面装饰层。打磨结束后，用抛光剂对边缘进行抛光处理。可使用人造大理石的抛光蜡作为抛光剂，抛光程序如下:

During sanding, the edges shall be sanded with 80 ＃, 220 ＃ and 320 ＃ sandpaper in sequence. The grinding speed is based on 2.5m/15-20min. When grinding, be careful not to damage the surface decorative layer. After polishing, polish the edges with polishing agent. The polishing wax of artificial marble can be used as polishing agent, and the polishing procedure is as follows:

a.用柔软的棉布沾取适量抛光蜡，对边缘进行擦拭；

a. Use a soft cotton cloth to dip an appropriate amount of polishing wax and wipe the edges;

b.待抛光蜡干燥后，再对边缘涂一层抛光蜡，并用布进行擦拭，使之出现光泽，再涂一层抛光蜡，并用干净的布擦拭，直至边缘光亮。

b. After the polishing wax is dry, apply a layer of polishing wax on the edge and wipe it with a cloth to make it shiny. Apply another layer of polishing wax and wipe it with a clean cloth until the edge is bright.

拼接板件时，应注意以下几点:

Pay attention to the following points when splicing plates:

a.粘合剂的涂布量需要控制在2.5-3.0g/cm2，并且要确保涂布到全部粘接表面；

a. The application amount of adhesive shall be controlled within 2.5-3.0g/cm2, and it shall be ensured that the adhesive is applied to all bonding surfaces;

b.拼接后，用夹子压合30分钟左右。竖直方向粘合时，一定要开口，增大粘合面，以确保粘合的强度；

b. After splicing, press with clips for about 30 minutes. When bonding in the vertical direction, be sure to open and increase the bonding surface to ensure the bonding strength;

c.一旦发现被粘合部件有爆口等缺陷，需要将光滑平整的一面朝外，以保证粘合的质量。

c. Once it is found that the bonded parts have defects such as bursting, the smooth and flat side needs to be outward to ensure the quality of bonding.

抗倍特板在安装结束时，如果表面出现斑点或污迹，可用毛巾沾取少量油性清洁剂(油与丙酮的混合物)轻轻擦拭去这些斑点或污点。如果没有斑点或污迹，用一般清洁剂如肥皂加水，或洗洁精加水擦拭即可。更多相关使用就来我们网站https://www.fumeijia.net咨询了解吧！

At the end of the installation of the anti magnification special plate, if there are spots or stains on the surface, use a small amount of oily cleaner (mixture of oil and acetone) dipped in a towel to gently wipe away these spots or stains. If there is no spot or stain, wipe it with general detergent such as soap and water, or detergent and water. Come to our website for more relevant use https://www.fumeijia.net Ask and understand!