山东创图建筑装饰工程有限公司
18660816658
您当前位置: 如何解决防火板加工时出现的爆边问题？
来源：https://www.fumeijia.net/ 日期：2021-05-07 发布人：admin
如何解决防火板加工时出现的爆边问题？
How to solve the problem of edge burst in the processing of fireproof board?
(一)、出现上面爆边
（1） The top edge appears
1、主锯片太钝，锯齿太少
1. The main saw blade is too blunt and the saw teeth are too few
2、主锯片高出板材太少
2. The main saw blade is too little higher than the plate
3、板材质量太差，会很快钝锯片
3. If the quality of the plate is too poor, the saw blade will be blunt soon
4、重新更换锯片
4. Replace the saw blade again
5、升高主锯片
5. Raise the main saw blade
6、选用杂质少、质量高的板材
6. Select the plate with less impurities and high quality
(二)、出现下面爆边(锯后的板材)
（2） There is edge burst below (sawn board)
1、副锯片太钝
1. The saw blade is too blunt
2、副锯宽度不够、太窄
2. The width of the auxiliary saw is not enough or too narrow
3、主、副锯片中间线不重合
3. The middle line of the main saw blade and the auxiliary saw blade does not coincide
4、重新更换锯片
4. Replace the saw blade again
5、换锯片或增加锯片厚度
5. Change saw blade or increase saw blade thickness
6、重新调整副锯左右位置
6. Readjust the left and right position of the auxiliary saw
(三)、有烧焦的痕迹(锯后板材上)
（3） There are burning marks (on the sawn plate)
1、合金锯片太钝，锯片上锯齿太多
1. The alloy saw blade is too blunt and there are too many teeth on the saw blade
2、转速过高或进料太慢
2. Too high speed or too slow feeding
3、更换锯片，选择适当的锯片
3. Replace the saw blade and select the appropriate one
4、选择适当的转速和进料速度
4. Select the appropriate speed and feeding speed
(四)、在锯切时有工件被副锯顶起来的现象
（4） During sawing, the workpiece is jacked up by the auxiliary saw
1、副锯片太钝
1. The saw blade is too blunt
2、副锯片升得太高
2. The auxiliary saw blade rises too high
3、更换锯片
3. Replace the saw blade
4、适当降低副锯片高度
4. Reduce the height of the auxiliary saw blade appropriately
(五)、中间贴面板爆边
（5） Edge burst of middle panel
1、板材较厚，每块微弯不平整，上下面互叠一起后产生缝隙
1. The plate is thick, each piece is slightly bent and uneven, and the upper and lower parts are overlapped to form a gap
2、机械压料的气缸压力不够
2. The cylinder pressure of mechanical pressing is not enough
3、工件板面有条纹(凹凸)也会爆边
3. The work piece plate surface has the stripe (concave convex) also can burst the edge
4、工作锯切时少压2-3块板材
4. Press 2-3 pieces less when sawing
5、锯切板材时进刀速度适当调慢适切认可
5. When sawing the plate, the feed speed should be adjusted to be appropriate
6、检查锯片是否不锋利，及时修磨刃口
6. Check whether the saw blade is not sharp, and repair the edge in time
感谢您的阅读，希望以上内容对您有所帮助，如您想了解更多精彩内容请点击我们的官网：富美家山东总代理http://www.fumeijia.net。
Thank you for your reading. I hope the above content will be helpful to you. If you want to know more wonderful content, please click our official website: fumika Shandong general agent http://www.fumeijia.net .
上一篇：UV快装板在家居装饰方面的应用！
下一篇：轻质复合墙板质量验收标准是什么？
Related products相关新闻
产品销售热线：18660816658
技术方案咨询：18560211715
仓库地址：山东省济南市天桥区金鑫产业园303仓库