Due to the fire board is a new industry in recent years, many users are not very familiar with the application of fireproof board. Today, fumihome explains the specific method for the use of fireproof board as partition wall.

　　使用的具体步骤：

　　The specific steps are as follows:

　　1．防火板材：一般情况下建议用6mm厚度以上的玻镁板作隔墙板。

　　1. Fireproof board: in general, it is recommended to use glass magnesium plate with thickness above 6 mm as partition board.

　　2．配件：6mm以上的板材固定在框架龙骨上，要用3.5200mm的沉头螺钉固定，钉头低于板面0.5mm，以便保证饰面平整。

　　2. Accessories: the plate with a diameter of more than 6 mm is fixed on the frame keel with a 3.5200 mm countersunk screw. The nail head is 0.5 mm lower than the plate surface to ensure the smooth finish.

　　3．安装：开始安装时，必须标好龙骨的准确位置，并作好记号。竖龙骨距离为450-600mm，墙体的连接处和门窗两侧安装时要装附加龙骨，如墙体高度大于2440mm时，须在板材连接处加装支撑龙骨。

　　3. Installation: at the beginning of installation, the accurate position of keel must be marked and marked. The center distance of vertical keel is 450-600mm. Additional keel shall be installed at the connection of wall and both sides of doors and windows. If the wall height is greater than 2440 mm, support keel shall be installed at the connection of plate.
                  

　　4．板距：相临板材之间留缝距4-6mm，板材与地面之间必须留有5mm的间隙，螺钉安装距为150mm，距板边10mm，距离板角30mm。

　　4. Plate distance: the seam distance between adjacent plates is 4-6mm, the gap between plate and ground must be 5mm, the center distance of screw installation is 150 mm, the distance from plate edge is 10 mm, and the distance from plate angle is 30 mm.

　　5．吊挂：卫生间或厨房间等吊挂重物处，必须用木板或龙骨加固，以免板材受到破坏。

　　5. Hanging: the toilet or kitchen and other hanging heavy objects must be reinforced with wood or keel to avoid damage to the board.

　　6．接缝处理：在安装时板材与板材留有间隙4-6mm，用107胶水或强力胶调匀后用刮刀涂抹板材及缝隙处，然后用纸带或风格带粘贴压平。

　　6. Joint treatment: during installation, there is a gap of 4-6 mm between plates. After mixing with 107 glue or super glue, smear the plate and gap with scraper, and then paste and flatten with paper tape or style tape.

　　7．涂料装饰：可以用喷涂、刷涂或滚涂，但刷涂时必须参看涂料的有关说明。

　　7. Coating decoration: spraying, brushing or rolling coating can be used, but the relevant instructions of coating must be referred to when brushing.

　　8．装饰面贴瓷砖：在浴室、卫生间、厨房、地下室等潮湿区域安装时，如需在板面贴瓷砖龙骨之间的距离必须缩短到400mm。墙体每隔三块板(约3.6mm左右)必须留有一条伸缩缝。

　　8. Decorative surface tiles: when installing in the bathroom, bathroom, kitchen, basement and other humid areas, if it is necessary to paste tiles on the board, the distance between keel must be shortened to 400mm. There must be an expansion joint in the wall every three boards (about 3.6mm).

　　9．隔音墙体：如需墙体有较高的隔音效果，必须要求墙体和板材结合紧密密闭，再向空墙内填充矿棉，如龙骨两面采用两种不同厚度的板时，隔间效果更佳。

　　9. Sound insulation wall: if the wall is required to have high sound insulation effect, the wall and plate must be tightly sealed, and then the hollow wall is filled with mineral wool. For example, when two different thickness plates are used on both sides of the keel, the compartment effect is better.

　　10．抗冲击墙体：建议您选用8mm以上的防火板或加一层板，第二张板须用长一些的螺丝钉加固。这种方法可增强抗冲击、隔热、隔音效果和防火性能。

　　10. Impact resistant wall: it is recommended that you select a fire-proof board above 8mm or add a layer of board. The second board must be reinforced with longer screws. This method can enhance shock resistance, heat insulation, sound insulation and fire resistance.

　　以上是关于防火板隔墙应用的方法介绍，想要了解更多内容欢迎点击富美家http://www.fumeijia.net网站。

　　The above is about the fire prevention board partition wall application method introduction, want to know more content, welcome to click the rich Meijia http://www.fumeijia.net Website.