1、 Vertical plane

步用专用切割工具将防火板材裁剪成所要求的规格，特别注意防火板材每一条边需多留6毫米当作压边的用处。饰面防火板附着到基层板上面时，个贴表面积较小的垂直面。

The first step is to cut the fireproof board into the required specifications with a special cutting tool, and pay special attention to the extra 6mm on each edge of the fireproof board as the purpose of edge pressing. When the facing fireproof board is attached to the base plate, the first vertical surface with small surface area shall be pasted.

施工过程时，基层板的边和封边条的后面都一定要上胶，上胶可以使用涂装和刮涂的具体方法。等约几分钟到十几分钟万能胶挥发掉干后，即万能胶不沾手时，将饰面防火板封边条谨慎贴到基层板的垂直线旁边去，随后再用滚轴或压力机加压力以保证饰面防火板黏贴到基层板上面，再将不必要的一部分修剪掉。这是水平面直接贴的方法。

During the construction process, the edge of the base plate and the back of the edge sealing strip must be glued. The specific methods of coating and scraping can be used for gluing. After the all-purpose adhesive evaporates and dries in a few minutes to more than ten minutes, that is, when the all-purpose adhesive does not touch your hands, carefully stick the edge sealing strip of the facing fireproof board next to the vertical line of the base plate, and then apply pressure with a roller or press to ensure that the facing fireproof board adheres to the base plate, and then trim the unnecessary part. This is the method of pasting directly on the horizontal plane.

二、水平面

2、 Horizontal plane

同样的，将强力胶站到防火板材背部和基材板水平面，直到强力胶不黏手时，将防火板材放进基材板上。要是黏贴的范围特别大，是能用木块先间隔时间着放到基材板上边，再将防火板材放进基材板上，等对正直再将木块抽出来，将防火板材慢慢地地挤压到基材板上。

Similarly, stand the strong glue on the back of the fireproof board and the horizontal plane of the base plate until the strong glue does not stick to your hand, and put the fireproof board on the base plate. If the scope of adhesion is particularly large, wood blocks can be placed on the base plate at intervals, and then the fire-proof plate can be placed on the base plate, and then the wood blocks can be pulled out after alignment, and the fire-proof plate can be slowly squeezed onto the base plate.

当饰面防火板被压贴到基材板时应注意将防火板之间的空气去除，然后应该再用滚轮用力压匀一次或送进冷压机里，或经过旋转滚筒来加压，务必使胶能均匀分布，同时避免残余的空气在里面。

When the facing fireproof board is pressed to the base plate, pay attention to remove the air between the fireproof boards, and then use the roller to press it evenly once, or send it into the cold press, or pressurize it through the rotating roller. Make sure that the glue can be evenly distributed and avoid residual air in it.

加压工作做好之后，就可以用修边机等工具将多余的边切去，然后再用较锋利的锉刀将接缝处锉得圆滑些。

After the pressure work is done, you can cut off the excess edge with tools such as trimming machine, and then file the joint more smoothly with a sharp file.

富美家抗菌板https://www.fumeijia.net主要是为您提供相关的行业知识，想要理解更多的知识及内容，请大家持续关注本站。

Fumeijia antibacterial board https://www.fumeijia.net It is mainly to provide you with relevant industry knowledge. If you want to understand more knowledge and content, please continue to pay attention to this website.