Doors are indispensable to every family and play an important role in our security. Therefore, the requirements for fire doors are always very strict. As a new type of fire doors, wooden doors are the product of high technology. Wooden fire doors can not only beautify our homes, but also increase our family safety. What are the attractive qualities of Fumeijia Fireproofing Board?

　　一、防火板具有丰富的表面纹理可供选择，木纹素色金属应有尽有。装修时一定要考虑的是装修一的风格，传统的防火门不使用防火板，难以保证风格的统一性。所以当室内装修使用一定纹理的表面纹理时，我们可以找与室内纹理相同的防火板来制作防火门，防火门销售厂家说。

　　1. Fire-proof boards have abundant surface texture to choose from, and there are all kinds of lignin non-ferrous metals. When decorating, we must consider the style of decoration. Traditional fire doors do not use fire panels, so it is difficult to ensure the unity of style. So when the interior decoration uses a certain texture of the surface texture, we can find the same texture as the interior fireproof board to make the fireproof door, the fire door vendor said.

　　二、富美家防火板可阻燃防潮、防虫、施工简单、不褪色、无甲醛。

　　2. Fumeijia fire-proof board is flame-retardant, moisture-proof, insect-proof, simple in construction, non-fading and formaldehyde-free.

　　防火门安装要点:

　　Installation points of fire door:

　　(1)线。根据设计要求的尺寸、高程和方向，画出木门防火门框的位置线。

　　(1) Line. According to the design requirements of size, elevation and direction, draw the position line of wood door fire door frame.

　　(2)站立门框。先拆下木质防火板门框下的固定板，每一门框内的高度大于门扇的高度30毫米以上的人，洞口两侧地面必须设置预留槽。门框一般在±0.00标高以下埋设20mm。框口的上、下尺寸应相同。允许误差< 1.5mm，对角线误差< 2mm。将木制防火门框用木楔临时固定在孔内，经校准后，固定木楔、门框铁脚与预埋铁板件焊接牢固。

　　(2) Standing doorframe. Firstly, remove the fixing board under the wooden fire-proof board door frame. For people whose height in each door frame is higher than the height of the door fan over 30 mm, reserved grooves must be set on the ground on both sides of the opening. The doorframe is usually buried below (+0.00) elevation by 20mm. The upper and lower dimensions of the frame mouth shall be the same. The allowable error is less than 1.5 mm and the diagonal error is less than 2 mm. The wooden fireproof door frame is temporarily fixed in the hole with a wooden wedge. After calibration, the fixed wooden wedge, the iron foot of the door frame and the embedded iron plate are firmly welded.

　　(3)安装门及附件。门框周围的木质防火板裂缝，应保证用1:2水泥砂浆或强度不小于10MPa的细石混凝土密植，与墙体形成整体;固化后，对孔、壁进行喷涂。涂装完毕后，安装门扇、五金配件及相关防火装置。门关闭后，门缝应均匀平整，打开自由携带，不得有过紧、过松和回弹现象。

　　(3) Installation doors and accessories. The cracks in the wood fireproof board around the door frame should be guaranteed to be closely planted with 1:2 cement mortar or fine stone concrete with strength not less than 10 MPa, forming an integral whole with the wall; after solidification, the holes and walls should be sprayed. After finishing painting, install doors and fans, hardware fittings and related fire protection devices. After the door closes, the door seam should be even and smooth, open and carry freely, and should not be too tight, too loose and springback phenomenon.

　　以上是富美家防火板厂家为大家整理的相关内容，想要了解更多内容，欢迎访问网站：http://www.fumeijia.net

　　Above is the relevant content of Fumeijia Fireproofing Board Manufacturer for you. For more information, please visit the website: http://www.fumeijia.net.