抗倍特板件拼接时应掌握几点
来源:https://www.fumeijia.net/ 日期:2022-11-16 发布人:admin
抗倍特板这种材料虽然大家都认识了,但可能还不是很清楚其中的注意事项,下面富美家抗倍特厂家就来给大家普及一下抗倍特板件拼接时应掌握几点。
Although we all know this material, we may not be very clear about the precautions. Now, Fumeijia Anti Beite Factory will popularize some points that should be mastered when splicing anti Beite plates.
a.粘合剂的涂布量应控制在2.5-3.0g/cm2,粘接表面要全部涂布到;
a. The coating amount of adhesive shall be controlled at 2.5-3.0g/cm2, and the bonding surface shall be completely coated;
b.拼接后用夹子夹紧30分钟左右。竖直方向粘合时一定要开口,使粘合面增大,以确保粘合强度;
b. Clamp for about 30 minutes after splicing. When bonding in the vertical direction, an opening must be made to increase the bonding surface to ensure the bonding strength;
c.一旦发现被粘合部件有爆口等缺陷应将光滑平整的一面朝外,以保证粘合质量。
c. Once it is found that the bonded parts have defects such as cracks, the smooth and flat side shall be outward to ensure the bonding quality.
此外抗倍特板在安装结束时如表面出现斑点或污迹,可用毛巾沾取少量油性清洁剂(油与丙酮的混合物)轻轻擦拭这些斑点或污点即可除去。如果没有斑点或污迹用一般清洁剂如肥皂加水,或洗洁精加水擦拭便可。
In addition, if there are spots or stains on the surface of the anti magnification special plate at the end of installation, the spots or stains can be removed by gently wiping them with a small amount of oily cleaner (mixture of oil and acetone) dipped in a towel. If there are no spots or stains, use a general cleaner such as soap and water, or detergent and water to wipe.


在加工边缘时普遍采用的工具是手提镂铣机。在进行作业前应清除板件表面的灰尘或异物,以免在板件表面留下划痕或刻痕。
Handheld router is widely used to process edges. Before operation, the dust or foreign matters on the surface of the panel shall be removed to avoid scratches or nicks on the surface of the panel.
镂铣机的加工速度应保持在2m/min为宜,如果镂铣刀刀刃角度较小而工件厚度又较厚时,镂铣机的加工速度应适当放慢。
The processing speed of the router should be kept at 2m/min. If the cutting edge angle of the router is small and the thickness of the workpiece is thick, the processing speed of the router should be appropriately slowed down.
另外铣刀刃的长度应大于加工件的厚度,以保证一次走刀能铣削出边缘的线型。走刀时镂铣刀应从高处逐步向低处下滑直至镂铣刀刃包容铣削边缘。
In addition, the length of the milling blade shall be greater than the thickness of the workpiece, so as to ensure that the line shape of the edge can be milled at one time. When cutting, the router should gradually slide down from the high to the low until the router edge contains the milling edge.
值得注意的是,走刀时一定要保持平稳,不要让镂铣机晃动。晃动会使工件的边缘形成不规则波纹,给后道砂磨抛光工序增加工作量,影响加工效率。
It is worth noting that the cutter must be moved steadily, and the router must not shake. Shaking will cause irregular ripples on the edge of the workpiece, which will increase the workload of the subsequent sanding and polishing process and affect the processing efficiency.
抗倍特板件拼接时应掌握的要点就讲解到这里了,您对此有什么需求或者问题就来我们网站https://www.fumeijia.net咨询看看吧!
So far are the key points that should be mastered when splicing the anti multiplier panels. If you have any needs or problems, please come to our website https://www.fumeijia.net Consult!
上一篇:洁净板如何维护才能够避免过早的更换呢?
下一篇:防火板表面偶尔出现毛刺的原因
Related products相关新闻