富美家抗倍特板材在砂磨时建议按顺序分别采用80＃、220＃和320＃砂纸对边缘进行砂磨，打磨速度以15-20分钟打磨2.5米长度为基准，打磨时应注意不要损坏表面装饰层，结束后用抛光剂对边缘进行抛光处理。抛光剂可使用人造大理石的抛光蜡，抛光程序如下：

During sanding, it is recommended to use 80 #, 220 # and 320 # sandpaper to sanding the edges. The sanding speed is based on the length of 2.5 m in 15-20 minutes. During sanding, attention should be paid to not damaging the surface decoration layer. After that, the edges should be polished with polishing agent. The polishing agent can use the polishing wax of artificial marble, and the polishing procedure is as follows:

a.用柔软的棉布沾取适量抛光蜡，对边缘进行擦拭；

a. Dip a proper amount of polishing wax with a soft cotton cloth and wipe the edge;

b.待抛光蜡干燥后再对边缘涂一层抛光蜡，并用布进行擦拭，使之出现光泽，后再涂一层抛光蜡并用干净的布擦拭，直至边缘光亮。

b. After the polishing wax is dry, apply a layer of polishing wax on the edge and wipe it with a cloth to make it shiny. Then apply a layer of polishing wax and wipe it with a clean cloth until the edge is bright.

6、板件拼接时应掌握以下几点:

6. The following points shall be mastered during plate splicing:

a.粘合剂的涂布量应控制在2.5-3.0g/cm2，粘接表面要全部涂布到；

a. The coating amount of adhesive shall be controlled at 2.5-3.0g/cm2, and the adhesive surface shall be coated completely;

b.拼接后用夹子夹紧30分钟左右。竖直方向粘合时一定要开口，使粘合面增大，以确保粘合强度；

b. Clamp with clamps for about 30 minutes after splicing. When bonding in the vertical direction, the opening must be opened to increase the bonding surface to ensure the bonding strength;

c.一旦发现被粘合部件有爆口等缺陷应将光滑平整的一面朝外，以保证粘合质量。

c. Once the bonded parts are found to have defects such as explosion, the smooth and flat side shall face outward to ensure the bonding quality.

此外，如要利用螺钉连接产品，应先用比螺钉直径小的钻头钻一个小孔然后向小孔注入粘合剂，再把螺钉拧入，并保证螺钉牙纹的上沿部分拧入5mm以上。

In addition, to connect products with screws, first drill a small hole with a drill bit smaller than the diameter of the screw, then inject adhesive into the small hole, and then screw in the screw, and ensure that the upper edge of the screw thread is screwed in more than 5mm.

钻杯状暗较链孔时板件的剩余厚度至少保留3mm以上，如剩余厚度过薄，杯状绞链埋入后会发生破损或出现凸痕。装暗较链时孔底和固定螺丝孔内应涂上粘合剂，然后再用螺钉拧紧。紧固螺钉时不要过度，否则也会使板件边缘部分外凸，严重时会将其顶破。

When drilling the cup-shaped dark chain hole, the remaining thickness of the plate shall be at least 3mm. If the remaining thickness is too thin, the cup-shaped hinge will be damaged or have convex marks after being embedded. When installing the dark chain, the adhesive shall be applied to the hole bottom and the fixing screw hole, and then the screw shall be tightened. Do not tighten the screws too much, otherwise the edge of the plate will be convex, and it will be broken in serious cases.

抗倍特板在安装结束时如表面出现斑点或污迹，可用毛巾沾取少量油性清洁剂（油与丙酮的混合物）轻轻擦拭这些斑点或污点即可除去。如果没有斑点或污迹用一般清洁剂如肥皂加水，或洗洁精加水擦拭便可。更多注意事项的了解就来关注我们网站https://www.fumeijia.net吧。

If spots or stains appear on the surface of the anti magnification plate at the end of installation, the spots or stains can be removed by gently wiping with a small amount of oily detergent (mixture of oil and acetone) with a towel. If there are no spots or stains, use general detergent such as soap and water, or detergent and water to wipe. For more information, please follow our website https://www.fumeijia.net Right.